Double Compression Brass Glands For Armoured Cable (Weatherproof)

Braco Double Compression Glands are manufactured out of brass rods/castings and are machined accurately to the required sizes. These are nickel plated to avoid corrosion whilst storage and use.
These glands have two moisture proof seals and may be used under most climatic conditions. These are weather proof and water proof and when protected by a PVC shroud, these can be used under most corrosive conditions. The armour cone and ring gives excellent mechanical and electrical connections.
These Glands are certified by Central Institute of Mining and Fuel Research, Dhanbad for use in weatherproof conditions. These Glands are rated with IP protection upto IP-65 Levels. These glands are as per BS 6121:Part 1:2005 and have parts: Brass body, Armour clamp and Ring, Gland Barrel sealing nut, two seals, , check nut and flat washer between the gland barrel and check nut is provided to prevent the drag on outer seal.
These glands are available in various different sizes and are suitable for all cables up to 1000sq. mm and control cables up to 61 cores. Threads can be ET / mm /NPT as per requirement. However if any special kind of gland or thread is required, the same can be supplied on request.
The gland can also be supplied with any other special plating such as cadmium, tin or pasivated. Also the glands can be supplied made out of aluminum, mild steel or stainless steel


  • Clamping cone will be provided with knurling for firm gripping of the armour.
  • Earthing tag will be provided if required at extra cost
  • PVC perotective shroud can be supplied at extra cost
  • Washers between seals are supplied for uniform radial gripping of PCP seals

Installation Instructions

Remove the outer sheath to the desired length depending on the lenght of the leads required and splay out the armour wire one by one and then cut the same according to the size of armour Clamping cone. File the sharp edges of the armour wire and for the gland as per assembly shown sectionally


  • Outer Seal
  • Sealing Nut
  • Brass Body
  • Clamping Ring
  • Armour Clamp
  • Inner Seal
  • Flat Washer
  • Check Nut
  • Gland Barrel

Technical Specification

BRACO CAT. NO B A A/F E A/C E1 Nipple thread Inch D Acceptable cable OD (mm)
ET MM NPT Above Upto
BPW-3/8'131121245/8"M161/2" NPT12812
BPW-1/2"151121245/8"M161/2" NPT12813
BPW-001S141321243/4"M201/2" NPT12813
BPW-5/8"171423263/4"M201/2" NPT151115
BPW-00117142427.53/4"M201/2" NPT1512.516.5
BPW-01S17.51525293/4"M201/2" NPT1512.516.5
BPW-01201427313/4"M201/2" NPT151518
BPW-01L201527311"M253/4" NPT151518
BPW-0220.51830.535.51"M253/4" NPT151820
BPW-02S20.51430.535.53/4"M201/2" NPT151820
BPW-03231830.535.51"M253/4" NPT152023
BPW-1"232030.535.51"M253/4" NPT152023
BPW-04282037431"M253/4" NPT152326
BPW-04L282437431-1/4"M321" NPT152326
BPW-05312541471-1/4"M321" NPT152630
BPW-05L312641471-1/2"M401-1/4" NPT152630
BPW-0634314754.51-1/2"M401-1/4" NPT153033
BPW-06S34244754.51-1/4"M321" NPT153033
BPW-07393351591-1/2"M401-1/4" NPT153337
BPW-08433854622"M501-1/2" NPT153741
BPW-09474056652"M501-1/2" NPT154146
BPW-01053446676.52"M501-1/2" NPT204652
BPW-010L53506676.52-1/2"M632" NPT204652
BPW-011615680922-1/2"M632" NPT205260
BPW-012686484973"M752-1/2" NPT206066
BPW-013S7367901043"M752-1/2" NPT206672
BPW-0137975981133-1/4"M823" NPT207278
BPW-01485781031193-1/2"M903" NPT207883
BPW-01598911121294"M1003-1/2" NPT248393
BPW-0161061041251444-1/2"M1154" NPT2593104